Check why AutoAir did not open the door Bosch SHPM65Z55N/01 Region: US | Content version: 2.0.0 Confirm cycle and option, then inspect the seal; leave hinge and installation work to service. MODEL AND MANUAL Exact model: SHPM65Z55N/01 Top controls with Start / Reset 3 sec, Delay and AutoAir. Match the full E-Nr, including /01. Manual: 9001411746_D · (0007) 640A MV Excludes: SHPM65Z55N/20; SHPM65Z55N/24; SHPM65W55N; Other SHPM / SHXM variants PREPARATION [ ] Wait for the cycle to finish and machine to cool. [ ] A door that slams shut or falls open needs service; do not operate with a faulty door mechanism. TOOLS - Soft damp cloth MATERIALS - Water FULL CHECKLIST 1. Confirm that AutoAir was enabled for a completed cycle. The rinse cycle does not automatically open the door. Follow the matching manual for its setting. Source: Bosch SHPM65Z*** Operating instructions; pp. 8, 37–38, 44 2. Check for visible dirt at the door and seal. Use the linked seal-cleaning task if needed, after disconnecting power safely. Source: Bosch SHPM65Z*** Operating instructions; pp. 8, 37–38, 44 3. Observe whether the cool door holds position halfway/fully open and closes gently when partly open. Stop using the unit if it slams or falls open. Source: Bosch SHPM65Z*** Operating instructions; pp. 8, 37–38, 44 4. If AutoAir still does not work, ask an installer or service technician to assess leveling and countertop clearance. Do not lower the unit, adjust hinges or change the installation here. Source: Bosch SHPM65Z*** Operating instructions; pp. 8, 37–38, 44 STOP CONDITIONS - Stop using the dishwasher for smoke, a burning smell, damaged wiring, an active leak or water near electrical equipment. Isolate power and water only from a safe, dry, accessible location; otherwise keep clear and request qualified help. - Do not remove the pump cover, reach into the pump, open electrical panels, bypass the door interlock or move the installed dishwasher. Refer plumbing connections, installation and repairs to qualified service. - Stop if a part is cracked, jammed, sharp, insecure or different from the matching manual. Do not force a fitting or touch hot water. Never mix cleaning products. BRANCH CHECKS Begin with: Was this a completed cycle other than Rinse? Was this a completed cycle other than Rinse? Was this a completed cycle other than Rinse? AutoAir opening is not expected for the Rinse cycle or before completion. Follow checklist steps: 1 - A non-Rinse cycle completed -> Continue to: Was AutoAir enabled using the matching manual?. - It was Rinse or the wash did not finish -> Observation and next step recorded. The cycle, disabled option or seal condition provides a next step. Complete that correction before assessing automatic opening; do not adjust hinges, leveling or countertop clearance yourself. - I have not checked this, or cannot observe it safely -> Observation still needed. This check is not complete. A condition you have not observed is still unknown. Save the record and return when the preparation and observation can be completed safely; ask support if safe access is uncertain. Was AutoAir enabled using the matching manual? Was AutoAir enabled using the matching manual? The feature is configurable. Do not infer its setting from the door staying closed. Follow checklist steps: 1 - The enabled setting is confirmed -> Continue to: Does the cool door hold halfway or fully open and close gently from partly open?. - The setting was off -> Observation and next step recorded. The cycle, disabled option or seal condition provides a next step. Complete that correction before assessing automatic opening; do not adjust hinges, leveling or countertop clearance yourself. - I have not checked this, or cannot observe it safely -> Observation still needed. This check is not complete. A condition you have not observed is still unknown. Save the record and return when the preparation and observation can be completed safely; ask support if safe access is uncertain. Does the cool door hold halfway or fully open and close gently from partly open? Does the cool door hold halfway or fully open and close gently from partly open? Keep clear of the door path. Do not use a door that slams shut or falls open. Follow checklist steps: 3 - Door movement matches these observations -> Continue to: Are the door edges and seal clean?. - The door slams, falls open or will not hold position -> Pause and request qualified help. The observed condition needs qualified help. Keep the appliance out of use when a safety concern remains. Share the exact model, displayed message and your before/after observations; do not open panels, bypass a lock or access the pump. - I have not checked this, or cannot observe it safely -> Observation still needed. This check is not complete. A condition you have not observed is still unknown. Save the record and return when the preparation and observation can be completed safely; ask support if safe access is uncertain. Are the door edges and seal clean? Are the door edges and seal clean? Use the seal-cleaning task with power safely isolated if residue is visible. Follow checklist steps: 2 - The seal is clean or has been cleaned -> Continue to: Did AutoAir open the door after the next eligible completed cycle?. - Residue remains or the seal is damaged -> Observation and next step recorded. The cycle, disabled option or seal condition provides a next step. Complete that correction before assessing automatic opening; do not adjust hinges, leveling or countertop clearance yourself. - I have not checked this, or cannot observe it safely -> Observation still needed. This check is not complete. A condition you have not observed is still unknown. Save the record and return when the preparation and observation can be completed safely; ask support if safe access is uncertain. Did AutoAir open the door after the next eligible completed cycle? Did AutoAir open the door after the next eligible completed cycle? Keep the opening area clear; do not pull the door to imitate automatic release. Follow checklist steps: 4 - The door opened automatically -> Observed result recorded. You observed automatic opening after a completed eligible cycle. This is your observation, not independent confirmation of the appliance condition. - It stayed closed with AutoAir enabled -> Pause and request qualified help. The observed condition needs qualified help. Keep the appliance out of use when a safety concern remains. Share the exact model, displayed message and your before/after observations; do not open panels, bypass a lock or access the pump. - I have not checked this, or cannot observe it safely -> Observation still needed. This check is not complete. A condition you have not observed is still unknown. Save the record and return when the preparation and observation can be completed safely; ask support if safe access is uncertain. RESULT OBSERVATIONS - You observed automatic opening after a completed eligible cycle. YOUR RECORD Observation date: ____________________ BEFORE AutoAir conditions: ____________________ AFTER Door and eligible-cycle observations: ____________________ Additional observations: ____________________ Result / reason for stopping: ____________________ Next action: ____________________ REMINDER Choose a reminder to review this observation when the symptom recurs or care is needed; no fixed day interval is assigned. Interval: Choose a personal interval; basis: user-selected Source: bosch-manual; pp. 8, 37–38, 44 A calendar reminder is a personal plan, not a record of work completed. DIAGRAMS Conceptual door-seal inspection points and normal door-motion observations; no hinge adjustment or gasket-removal instructions. https://csl-13-appliance-repair.pages.dev/diagrams/bosch-door-seal.svg Original Homekeep schematic; conceptual identification and observation only, not an exact part drawing or official Bosch artwork SOURCES Bosch SHPM65Z*** Operating instructions | 9001411746_D · (0007) 640A MV | pp. 8, 37–38, 44 https://media3.bsh-group.com/Documents/9001411746_D.pdf#page=37 Checked: 2026-10-13. Copyright BSH. Linked reference; original summaries only. No manual illustrations reproduced. Bosch SHPM65Z55N/01 appliance information | Live E-Nr /01 support page | Exact SHPM65Z55N/01 identity; associated operating instructions 9001411746_D https://www.bosch-home.com/us/en/productservice/SHPM65Z55N-01 Checked: 2026-10-13. Link only RELATED TASKS Wipe the dishwasher door seal and edges: https://csl-13-appliance-repair.pages.dev/tasks/bosch-door-seal/ Check dishes that stay wet: https://csl-13-appliance-repair.pages.dev/tasks/bosch-poor-drying/ Observations do not certify a physical repair. Follow your matching supplied manual and the stop conditions. Guide: https://csl-13-appliance-repair.pages.dev/tasks/bosch-autoair/