Check standing water after a cycle Bosch SHPM65Z55N/01 Region: US | Content version: 2.0.0 Confirm the cycle finished, inspect the filter and report external drainage clues. MODEL AND MANUAL Exact model: SHPM65Z55N/01 Top controls with Start / Reset 3 sec, Delay and AutoAir. Match the full E-Nr, including /01. Manual: 9001411746_D · (0007) 640A MV Excludes: SHPM65Z55N/20; SHPM65Z55N/24; SHPM65W55N; Other SHPM / SHXM variants PREPARATION [ ] Let water and interior cool; disconnect power before touching filters. [ ] Do not open the pump cover here. Watch for glass or sharp debris. TOOLS - Soft brush if the separate filter task is needed MATERIALS - No added cleaning chemicals FULL CHECKLIST 1. Record where water is visible and whether the last cycle completed. Do not infer a faulty pump or a drain-volume limit from water alone. Source: Bosch SHPM65Z*** Operating instructions; pp. 8, 36, 38–40, 43, 46 2. For a safe unfinished cycle, use the separate cycle-reset task: hold Start about 3 seconds to 0:01, close the door as required for top controls, allow about 1 minute for draining and switch off. Do not repeat if water escapes. Source: Bosch SHPM65Z*** Operating instructions; pp. 8, 36, 38–40, 43, 46 3. Allow the interior to cool and isolate power safely. Inspect the filter system using the complete filter-cleaning task; clean and lock it if needed. Leave the pump cover closed. Source: Bosch SHPM65Z*** Operating instructions; pp. 8, 36, 38–40, 43, 46 4. From the reachable under-sink area, observe the drain hose for a visible kink and note whether the household sink backs up. Do not move the dishwasher or disconnect plumbing. Source: Bosch SHPM65Z*** Operating instructions; pp. 8, 36, 38–40, 43, 46 5. If the cycle completed and visible checks give no safe correction, request qualified drainage assessment. Record any displayed code and the observations instead of selecting a replacement part. Source: Bosch SHPM65Z*** Operating instructions; pp. 8, 36, 38–40, 43, 46 STOP CONDITIONS - Stop using the dishwasher for smoke, a burning smell, damaged wiring, an active leak or water near electrical equipment. Isolate power and water only from a safe, dry, accessible location; otherwise keep clear and request qualified help. - Do not remove the pump cover, reach into the pump, open electrical panels, bypass the door interlock or move the installed dishwasher. Refer plumbing connections, installation and repairs to qualified service. - Stop if a part is cracked, jammed, sharp, insecure or different from the matching manual. Do not force a fitting or touch hot water. Never mix cleaning products. BRANCH CHECKS Begin with: Was the last cycle definitely completed? Was the last cycle definitely completed? Was the last cycle definitely completed? A stopped wash needs to be separated from a completed wash before drawing a drainage conclusion. Follow checklist steps: 1 - Yes, it finished -> Continue to: Is the visible filter system clean, intact and locked?. - No, it was interrupted -> Continue to: Did one normal reset drain the unfinished cycle?. - I have not checked this, or cannot observe it safely -> Observation still needed. This check is not complete. A condition you have not observed is still unknown. Save the record and return when the preparation and observation can be completed safely; ask support if safe access is uncertain. Did one normal reset drain the unfinished cycle? Did one normal reset drain the unfinished cycle? Use the reset task only with a safe appliance and dry surrounding area. Follow checklist steps: 2 - The cycle ended and the standing water cleared -> Observed result recorded. You recorded that the standing-water symptom cleared after an observed cycle or reset. This is your observation, not independent confirmation of the appliance condition. - Standing water remains after the reset -> Continue to: Is the visible filter system clean, intact and locked?. - I have not checked this, or cannot observe it safely -> Observation still needed. This check is not complete. A condition you have not observed is still unknown. Save the record and return when the preparation and observation can be completed safely; ask support if safe access is uncertain. Is the visible filter system clean, intact and locked? Is the visible filter system clean, intact and locked? Cool and isolate before touching it. No pump-cover access is part of this task. Follow checklist steps: 3 - The filters are clean and locked -> Continue to: Is the accessible drain route free of an obvious kink or sink backup?. - Food, damage or incorrect seating needs attention -> Observation and next step recorded. The filter or visible drain-route condition is an actionable clue. Complete the filter task or ask an installer/plumber to assess the drainage route before another comparison; no pump failure is inferred. - I have not checked this, or cannot observe it safely -> Observation still needed. This check is not complete. A condition you have not observed is still unknown. Save the record and return when the preparation and observation can be completed safely; ask support if safe access is uncertain. Is the accessible drain route free of an obvious kink or sink backup? Is the accessible drain route free of an obvious kink or sink backup? An inaccessible section remains unknown; never pull the appliance out to inspect it. Follow checklist steps: 4 - The visible route has no obvious restriction -> Continue to: Does water still remain after a completed cycle and the visible checks?. - A visible kink or household drain backup is present -> Observation and next step recorded. The filter or visible drain-route condition is an actionable clue. Complete the filter task or ask an installer/plumber to assess the drainage route before another comparison; no pump failure is inferred. - I have not checked this, or cannot observe it safely -> Observation still needed. This check is not complete. A condition you have not observed is still unknown. Save the record and return when the preparation and observation can be completed safely; ask support if safe access is uncertain. Does water still remain after a completed cycle and the visible checks? Does water still remain after a completed cycle and the visible checks? Record the completion state and any code for service; do not open the pump. Follow checklist steps: 5 - The water has cleared and no recurrence was observed -> Observed result recorded. You recorded that the standing-water symptom cleared after an observed cycle or reset. This is your observation, not independent confirmation of the appliance condition. - The standing-water symptom remains -> Pause and request qualified help. The observed condition needs qualified help. Keep the appliance out of use when a safety concern remains. Share the exact model, displayed message and your before/after observations; do not open panels, bypass a lock or access the pump. - I have not checked this, or cannot observe it safely -> Observation still needed. This check is not complete. A condition you have not observed is still unknown. Save the record and return when the preparation and observation can be completed safely; ask support if safe access is uncertain. RESULT OBSERVATIONS - You recorded that the standing-water symptom cleared after an observed cycle or reset. YOUR RECORD Observation date: ____________________ BEFORE Water and cycle history: ____________________ AFTER Drainage observations: ____________________ Additional observations: ____________________ Result / reason for stopping: ____________________ Next action: ____________________ REMINDER Choose a reminder to review this observation when the symptom recurs or care is needed; no fixed day interval is assigned. Interval: Choose a personal interval; basis: user-selected Source: bosch-manual; pp. 8, 36, 38–40, 43, 46 A calendar reminder is a personal plan, not a record of work completed. DIAGRAMS Conceptual supply and drainage routes below a sink, with only visible hose sections inspected; no routing dimensions or plumbing alterations. https://csl-13-appliance-repair.pages.dev/diagrams/bosch-water-route.svg Original Homekeep schematic; conceptual identification and observation only, not an exact part drawing or official Bosch artwork SOURCES Bosch SHPM65Z*** Operating instructions | 9001411746_D · (0007) 640A MV | pp. 8, 36, 38–40, 43, 46 https://media3.bsh-group.com/Documents/9001411746_D.pdf#page=46 Checked: 2026-10-13. Copyright BSH. Linked reference; original summaries only. No manual illustrations reproduced. Bosch SHPM65Z55N/01 appliance information | Live E-Nr /01 support page | Exact SHPM65Z55N/01 identity; associated operating instructions 9001411746_D https://www.bosch-home.com/us/en/productservice/SHPM65Z55N-01 Checked: 2026-10-13. Link only RELATED TASKS Clean and lock the dishwasher filters: https://csl-13-appliance-repair.pages.dev/tasks/bosch-filter-clean/ End a saved cycle and select a new one: https://csl-13-appliance-repair.pages.dev/tasks/bosch-cycle-reset/ Trace dishwasher odor to visible residue or drainage: https://csl-13-appliance-repair.pages.dev/tasks/bosch-odor/ Observations do not certify a physical repair. Follow your matching supplied manual and the stop conditions. Guide: https://csl-13-appliance-repair.pages.dev/tasks/bosch-standing-water/